RFLink: Firmware Change Log - Last stable release:

12/01/2024

RFLink v1.1 - R51: (12/01/2024)
- New Device: Unitec W186-F Temperature sensor
- New Device: Amazon Basics Meat Thermometer
- New Device: Valoin Wireless Digital Meat Thermometer With Dual Probe
- New Device: Atech-WS308 temperature sensor
- New Device: Auriol 4-LD5661, Auriol 4-LD5972, Auriol 4-LD6313 temperature & rain sensor
- New Device: Auriol AFT77B2 temperature sensor
- New Device: Auriol AFW2A1 temperature & humidity sensor
- New Device: Auriol AHFL 433B2 IPX4 temperature & humidity sensor
- New Device: Auriol HG02832, Auriol HG02832D temperature & humidity sensor
- New Device: Rubicson 48957 temperature & humidity sensor
- New Device: Baldr rain meter
- New Device: Rainpoint rain meter
- New Device: TFA-Dostmann-30.3222.02 Combi Sensor Thermo/Hygro/Wind
- New Device: TX141-BV3
- Fixed: Funkbus handling
- Fixed: Acurite extremely low temperature value handling
- Fixed: LightwaveRF handling
- Fixed: Milight handling
- Added: Hager additional command information
- Changed: Additional optimizations

RFLink: Firmware Change Log - Last stable release:

24/12/2023

RFLink v1.1 - R50: (24/12/2023)
- New Device: Abalon Curtain remote (BE301) (receive)
- New Device: Lanboo Curtain remote (receive)
- New Device: Zaffer Blinds remote (receive)
- New Device: Marimex Pool Thermometer
- New Device: Gira 2255 00
- New Device: Deltia 8.33 - Thermostat - X2D - New Device: Deltia 8.03 - Thermostat - X2D REF 6050417
- New Device: Deltia 1.03 - 3 zone - X2D (including support for pairing/association)
- New Device: Calybox 220 - 3 zone - X2D
- New Device: DPM Switch sets (Thanks: Olaf)
- New Device: Universal Blyss receptor ref 582857
- Added: KAKU APIR-2150
- Added: KAKU AWST-6000
- Added: Acurite 899 rain meter (Thanks: Peter)
- Added: Funkbus transmit
- Added: Another Chinese screen motor set following a Dooya variant
- Added: Additional Hager support
- Added: Oregon THN129
- Added: Broadlink SmartOne S1C sensors
- Added: Tellstick Temperature and humidity sensors (Thanks: Ivan)
- Added: Viking 02038 Temperature and Humidity sensor
- Added: Viking 02042 Temperature sensor and Rain meter
- Added: option to force WH2 protocol for some sensors in case of incorrect detection
- Fixed: HomeEasy HE100
- Fixed: Froggit F007TH decoding issues
- Fixed: Viking negative temperatures
- Fixed: Alecto V4 better handling when multiple devices are used
- Fixed: Conrad Pool Thermometer recognition
- Fixed: Banggood SKU174397 allowing multiple devices
- Fixed: Various changes to RTS to improve detection
- Changed: massive overhaul of the code to clean up and free important resources
- Changed: RTS: Increased number of supported devices to 32
- Removed: QRFdebug, use RFDebug for all logging

RFLink: Firmware Change Log - Last stable release:

18/10/2017

RFLink v1.1 - R48: (18/10/2017)
- New Device: British Gas RC Plus Thermostat
- New Device: Drayton Digistat +2RF Thermostat
- New Device: Worcester Bosch DT10RF Thermostat
- New Device: Danfoss TP4000 Thermostat
- New Device: Vaillant VRT 340f Thermostat
- New Device: CalorMatic 340f Thermostat
- New Device: Hager Flash Thermostat
- New Device: Thermoflash Thermostat
- New Device: Piloteco Thermostat
- New Device: Sanfil Thermostat
- New Device: Monomat Thermostat
- New Device: Micromat Thermostat
- New Device: Monotron Thermostat
- New Device: Mémoprog RF Thermostat
- New Device: Calidou Plus Thermostat
- New Device: Radiafonte II Thermostat
- New Device: Bellagio II Thermostat
- New Device: Verplus Thermostat
- New Device: Palatino Thermostat
- New Device: Verlys Evolution Thermostat
- New Device: Melody Evolution Thermostat
- New Device: Millenium Triphasé Thermostat
- New Device: Sensual SAS Thermostat
- New Device: Sensual Bains Thermostat
- New Device: Athena Millenium Thermostat
- New Device: Athena Plenitude Thermostat
- New Device: Brel (and compatible) light switch
- New Device: Beurer BG64 (and possibly BF100) scales
- New Device: Falmec hoods
- Added: support for X10 Marmitec DS90/DS91 tamper switch
- Fixed: Milight color issue
- Fixed: Milight brightness issue
- Fixed: Milight RGB-CCT pairing made easier with pair/unpair commands - Fixed: Milight CRC calculation on some of the protocol versions
- Fixed: Improved Kerui D025/D026 handling
- Fixed: Improved Mertik filtering
- Fixed: bug with Europe switchset unit numbers
- Fixed: Corrected TFA timing
- Fixed: Improved Cresta packet filtering

RFLink: Firmware Change Log:

15/09/2017

RFLink v1.1 - R47: (15/09/2017)
- New Device: Micro Tybox X2D / Tybox H X2D Thermostats (works with 433 and/or 868 mhz)
- New Device: Tybox 310 X2D Thermostat (868mhz)
- New Device: Delta Dore - Deltia 8.03 X2D Thermostat (868mhz)
- New Device: TYXIA 261/461 X2D micro modules (868mhz) (Receive only, more logs needed)
- New Device: Milight RGB+CCT (a.o. 4-zone FUT092/ 8-zone FUT089)
- New Device: Milight RGB (a.o. FUT098)
- New Device: Bofu motor BF-301, EY1612, EY1624 and others
- New Device: Oregon Scientific SL109
- New Device: AR53002 / AR50055 X2D Thermostats
- New Device: Atlantic MD-210R / Focus MD-210R - 868mhz door contact
- New Device: Legrand CAD Radio
- New Device: Gelia EMW100T switch set
- New Device: ELEC EDB-40 / QH-1085TX V1.1 Quhwa doorbell
- New Device: X10 Sensors
- New Device: Ambient FT004T temperature sensor
- New Device: Ambient FT004B temperature sensor
- New Device: ASA radio technology Go-1
- New Device: Telis 4 Modulis RTS
- New Device: Added support for a new version of the Rubicson WT0122 pool thermometer
- New Device: Renkforce E0190TA and compatible temperature sensors
- New Device: Ematronic AC114-01B shutter/blinds controller
- New Device: Yooda Melody shutter/blinds controller
- New Device: Viking 02813 Temperature sensor
- New Device: Marquant 943134 Temperature sensor
- New Device: Arlec RC10 switch set
- New Device: V2 Phoenix remote signals (Receive only)
- New Device: IDK CAR-200 doorbell (Receive only)
- New Feature: GPIO pin state at boot can be selected with a wire from pin 5 to ground to set the pin default to high
- Added: X2D/X3D protocol support
- Added: Milight RGB and RGB+CCT protocol support
- Added: Direct dimming support for Flamingo and compatible devices
- Added: Additional WH3 detection
- Added: Two Additional Dooya protocol flavors
- Added: Additional Dooya signal recognition
- Added: Additional Blyss remote control recognition
- Added: Additional Brell remote control recognition
- Added: STOP command support to (first) extended RTS protocol version
- Added: Support for second extended RTS protocol version
- Added: Additional Pair option for Bofu motor devices
- Added: upon request added 6 additional GPIO pin's for generic use
The GPIO pins are often used to 'press buttons' on incompatible devices
- Fixed: Added pairing command for Ansluta
- Fixed: Increased transmission duration for Ansluta
- Fixed: corrected barometric pressure value of BTHR918
- Fixed: UPM Esic negative temperatures
- Fixed: Further improved X10 protocol detection
- Fixed: 'newkaku' send command handling improved
- Fixed: 'newkaku' group commands put at a unique switch number
- Fixed: imrpoved newkaku filtering
- Fixed: improved Acurite SL109 negative temperature handling
- Fixed: CM113 ampere precision
- Fixed: Milight: bug in unit selection
- Fixed: bug with the number of RFCustom records
- Fixed: removal of RFCustom records
- Fixed: Improved Xiron sensor detection
- Fixed: Alecto rain meter values

RFLink: Firmware Change Log:

10/03/2017

RFLink v1.1 - R46: (10/03/2017)
- New Device: Applidom DM82 motion sensor
- New Device: OWL Intuition PV / CM180i
- New Device: WH2A temperature sensors
- New Device: WH1285 TX (WH-5) Temp & Humidity sensor
- New Device: ABB lightswitch type 3299a-11900 (a.k.a. TX Tango) (Receive only!)
- New Device: Velleman VM130T Motor control
- New Device: HRC 101 Motor control
- New Device: AC512-02 AC to RF projection screen trigger
- New Device: 2 new Dooya protocol flavors
- New Device: D-YA / Diya Motor control
- New Device: Konx doorbell model 602 (Receive only!)
- New Device: Doorman doorbell (Receive only!)
- New Device: Acurite 3in1 3N1TXR / 3N1TXC (Thanks: JR)
- New Device: Byron BY532E (Receive only!)
- New Device: Stagnoli remotes
- New Device: Blyss temperature sensors (Ref.630467) (Thanks: JD)
- New Device: Grundig QH-831A 2010525 & Quhwa QH-831A doorbell
- New Device: 868mhz: Woonveilig security sensors
- New Device: 868mhz: Egardia security sensors
- New Device: 868mhz: Alecto WS3900
- New Device: Yale HSA3000/6000 alarm system sensors
- New Device: Sartano 50080 (Harald Nyborg 2794) switch set
- New Device: Astrell 85 portal motorization system
- New Device: Philips AJ7010/12
- New Feature: Learn RF device signals that use a standard EV1527/PT2262 protocol
- Fixed: Some small eeprom handling issues
- Fixed: Improved AI protocol priority handling
- Fixed: various CC2500 issues, make sure pin 6 is wired to ground to use CC2500!
- Fixed: Tightened Warema EWFS detection
- Fixed: RTSlongTX command
- Fixed: ON/OFF vs UP/DOWN command handling
- Fixed: UPM Esic extended packet detection and increased sanity checks on data
- Fixed: Optimized Novatys timing
- Fixed: AlectoV3 Humidity value validation
- Fixed: FineOffset vs Alecto improved differentiation, Note: device ID's have changed for WS1100
- Fixed: Alecto WS-1100 humidity
- Fixed: AlectoV4 Some packets contained an invalid temperature
- Fixed: Globaltronics GT-WT-02 negative temperature/channel number mixup
- Fixed: Globaltronics GT-WT-02 now always reporting a humidity
- Fixed: Tristate send, removed debug message and fixed a timing bug
- Fixed: WS7000 rain reporting
- Fixed: Added additional Brel protocol variant
- Fixed: LightwaveRF turned MOOD commands into regular switch commands so any home automation software can use them
- Fixed: Improved Friedland doorbell signal detection
- Fixed: Acurite 5in1 corrected wind speed, wind direction and rainfall values (Thanks: Xztraz.)
- Fixed: Improved AcuRite 00592TXR detection
- Fixed: Tunex zero humidity value
- Fixed: Improved Home Confort transmit routine and added up/down support (Thanks: Geert)
- Fixed: Battery detection in Prologue protocol
- Fixed: Added channel number to device ID for THGR810
- Fixed: Added channel number support to Warema devices
- Fixed: Improved UPM ESIC protocol detection
- Fixed: Improved SA33 detection
- Fixed: Gaposa protocol timing
- Added: battery status on various Alecto/Maplin devices (Thanks: Ad)
- Added: Hardware & Software configuration via i/o pins:
pin 6 to ground for: CC2500 enable
pin 7 to ground for: disable internal pull-up on RF data in
pin 12 to ground for: reset of EEPROM settings

RFLink: Firmware Change Log:

7/12/2016

RFLink v1.1 - R45: (7/12/2016)
- New Device: Silvercrest switch set IAN276299
- New Device: Silvercrest switch set IAN113854
- New Device: Silvercrest switch set IAN91210
- New Device: Quigg switch set GT-9000 (Tevion/Globaltronics/ALDI)
- New Device: Unitec switch set 4811 model 50028 (Intertek)
- New Device: Cotech switch set 36-6361
- New Device: Sartano switch set, Model 50028, HN 10047
- New Device: Electro Depot switch set, article code 940557
- New Device: BL999 weather sensor
- New Device: Digi-Tech 4-LD14554 Outdoor temperature sensor (Thanks: PJA)
- New Device: PLC-T4022G X10 RF to Powerline
- New Device: X10 UR76 E Remote Control
- New Device: Konig Alarm system sensors
- New Device: Alecto 1200 alternative protocol version
- New Device: Oregon EW99
- New Device: Smartwares RM174RF Smoke detector
- New Device: FirstLine FWS802 Pool Thermometer (Thanks: BC)
- New Device: Liwin Shutters / Blinds controller
- Fixed: MiniGPIO command structure
- Fixed: Conrad RSL pair command added
- Fixed: Warema EWFS (Thanks: SH)
- Fixed: Removed Ningbo debug message
- Fixed: Mebus protocol detection for Auriol Z29536 IAN55982
- Fixed: Removed debug messages on Atlantic protocol
- Fixed: Milight color and brightness changing on groups
- Fixed: DKW2012 Humidity conversion
- Fixed: DKW2012 Wind speed conversion (Thanks: HJ)
- Fixed: Xiron ID sometimes had an incorrect bit
- Fixed: Blyss/Avidsen transmit
- Fixed: Aster protocol split on/off and dim/bright into separate devices
- Fixed: Improved detection of WH5029
- Fixed: Improved HE800 protocol detection
- Fixed: Improved detection of Cleverwatts, Kerui and compatible devices
- Fixed: Proper handling of incoming serial commands for KAKU and related devices
- Fixed: Improved Chacon EMW200 detection
- Added: RTS protocol option to swap ON/OFF command
- Added: RTS long TX option to extend the RTS transmit time
- Added: "Settings reset" feature
- Added: Extended Gaposa protocol
- Added: Lacrosse V3 protocol support for negative temperature values

RFLink: Firmware Change Log:

27/10/2016

RFLink v1.1 - R44: (27/10/2016)
- New Device: Ikea Ansluta (2.4 Ghz device, CC2500 transceiver required)
- New Device: Philips Living Colors Generation 1 (2.4 Ghz device, CC2500 transceiver required)
- New Device: Friedland DC44
- New Device: Warema EWFS shutters and awnings (Thanks: SH)
- New Device: Bosch DID09T951, Bosch DID09T950 and compatible ventilation units
- New Device: Siemens SF-01 and compatible ventilation units
- New Device: Wave Design SF-01 and compatible ventilation units
- New Device: Visonic MCT-302 open and close signal
- New Device: Ningbo KD-205-1 switch set
- New Device: Steffen Power Switch (1204380 3M)
- New Device: Bresser weather sensor
- New Device: RFTech 210TX weather sensor
- New Feature: Bluetooth LE Advertisement packet sniffing experimental (NRF24L01 required, needs to be wired for MiLight)
- New Feature: MySensors packet sniffing experimental (NRF24L01 required, needs to be wired for MiLight)
- New Device: MySensors temperature and humidity devices (more types to follow) (NRF24L01 required, needs to be wired for MiLight)
- Fixed: Improved OWL CM130 recognition
- Fixed: Revolt power reporting corrected
- Fixed: RFmeter values presented in hexadecimal
- Fixed: Improved Baldr signal recognition
- Added: Friedland PIR checksum calculation
- Added: GPIO 4 input and 4 output pins can be used as on/off or push button devices

RFLink: Firmware Change Log:

23/9/2016

RFLink v1.1 - R43: (23/9/2016)
- New Device: MiLight WW/CW remote & Bulbs
- New Device: WH3 temperature sensors
- New Device: Alecto 1300 Wireless Plant Monitor
- New Device: Unitec W235 Climate sensor
- New Device: Jula / Marquant 943134 temperature sensor
- New Device: Inovalley SM200
- New Device: DC250 motor controller
- New Device: Maplin Weather Station N96GY, Fine Offset WH1080, Fine Offset WH1081, Watson W-8681,
Digitech XC0348 Weather Station, PCE-FWS 20, Elecsa AstroTouch 6975, Froggit WH1080
- New Device: Loh Electronics 02812 Temperature and Humidity sensor
- New Device: Excelvan weather station
- New Device: Master Electrician RC-012-1-TR-009
- New Device: Home Confort STHI 100 temperature/humidity sensor
- New Device: Ditec Garage Door remote control
- New Device: Acurite 609TXC (alternative protocol)
- New Device: WS7000-27, WS7000-28 Thermometer
- New Device: WS7000-25 Thermo/Humidity, WS7000-22 Thermo/Humidity
- New Device: WS7000-19 Brightness Luxmeter
- New Device: Holtek HT6P20 (and compatible) Door, Window and PIR sensors (Thanks: Douglas Gazineu)
- New Device: Ambient Weather / Frogit F007TH
- New Device: Ambient Weather / Frogit F007T
- New Device: Ambient Weather / Frogit F007PF
- New Device: SelectPower switchset
- New Device: Profile led dasegno
- New Device: KERUI D026 Door Window Sensor
- New Device: LaCrosse TXT141-BV2
- New Device: Baldr B0317
- New Device: Atlantic MC-335 PIR
- New Device: RTS sensor protocol / Soliris
- New Device: RTS Extended protocol / Eolis 3D
- Fixed: Removed slash (/) from device names
- Fixed: Removed RTS and other debug data
- Fixed: Avidsen switch issue
- Fixed: Avidsen temperature data detection
- Fixed: Blyss & Avidsen pairing working correctly
- Fixed: AB440R signal detection
- Fixed: Chuango signal detection
- Fixed: Improved Promax detection
- Fixed: Additional check to make sure Milight send is not used when Milight support is disabled
- Fixed: WS2500-19 now correctly reporting Lux value
- Fixed: Milight RGBW Remote and WW/CW (Dual) Remote Control operating simultaneously with RGBW
- Fixed: Livolo On/Off state
- Fixed: Brel timing
- Fixed: Novatys detection
- Fixed: AMST606 detection issues
- Fixed: SelectRemote doorbell retransmission
- Fixed: Byron SX doorbell retransmissions
- Fixed: Byron SX doorbell recognition
- Fixed: Further improved the RF Environment Optimization System
- Fixed: improved the detection of Acurite devices
- Fixed: improved the detection of Cresta devices
- Fixed: improved the detection of Atlantic devices
- Added: NRF24L01 hardware detection, activating MiLight without NRF will result in MiLight being disabled
- Added: Smarthome YC-4000B protocol variant
- Added: New Brel protocol version
- Added: WS7000 protocol variant

RFLink: Firmware Change Log:

9/6/2016

RFLink v1.1 - R42: (9/6/2016)
- New Device: Mi-Light/LimitlessLED/Applamp/EasyBulb bridge functionality (2.4 Ghz, NRF24L01 with Milight wiring required)
- New Device: Hama SD-UN5-RF switch set
- New Device: Acurite Tower sensors
- New Device: Pollin PFR-130 Temperature & Rain meter
- New Device: Gaposa Blind/Shutter control (a.o. model QCT3S)
- New Device: Byron BY35 / BY301
- Added: Command "echo" function to auto create devices without the need of remote controls
- Added: Command "rtsrecclean 9" function to clean a single rolling code table entry
- Added: Command to invert the ON/OFF handling of the Tristate protocol
- Fixed: improved Atlantic MD-210R detection
- Fixed: improved DKW2012 detection to cover variations of the signal
- Fixed: Smarthome YC-4000B detection
- Fixed: improved RTS packet detection to prevent false positives
- Fixed: improved FA500 packet detection to prevent false positives
- Fixed: Modified X10 security sensor packet detection
- Fixed: Modified maximum humidity limit
- Fixed: Improved signal ARC detection
- Fixed: Chacon EMW200 detection
- Fixed: Nexa WST-512 detection
- Fixed: Oregon UV800
- Fixed: CM113 ID
- Added: Support for another MiLight remote variant

RFLink: Firmware Change Log:

18/4/2016

RFLink v1.1 - R41: (18/4/2016)
- Added: support for up to 3 OWL devices operating at the same time
- Fixed: Fine Offset without humidity value issue
- Fixed: Issue with some sensor types blocking other sensor types
- improved stability

RFLink: Firmware Change Log - Older versions:

10/4/2016

RFLink v1.1 - R40: (10/4/2016)
- New Device: Oregon Scientific RTHN318
- New Device: Halemeier HA-RHX-M2
- New Device: LaCrosse WS2315
- New Device: Lightwave Contact Switch
- New Device: Acurite 5in1
- New Device: XH110 temperature sensor
- New Device: Cresta WXR710XL
- New Device: Revolt NC-5461 Energy Meter, Otio, Profitec Funk Energiekosten Messgeraet
- New Device: Dooya RF Roller blinds (ao. AC123-16 and others)
- New Device: Envivo PO-1413 doorbell
- New Device: Synapse SN-1613 doorbell
- New Device: OWL +USB
- New Device: OWL Micro CM130
- New Device: Starlux ST101 PIR
- Fixed: Forrinx doorbell
- Fixed: WS2310 Windspeed issue with higher wind speeds
- Fixed: Livolo, Increased number of transmits
- Fixed: Conrad signal detection from Telstick Duo
- Fixed: Some LightwaveRF transmit cases
- Fixed: Keeloq, added button support
- Fixed: Extended XT200 signal range
- Fixed: Improved XT200/XH110, FineOffset & Alecto packet handling
- Fixed: Some Oregon sensor packets were missed
- Fixed: Oregon Humidity issue
- Fixed: Changed protocol name AOK to Dooya
- Fixed: added Dooya (and AOK) packet checksum
- Fixed: Mebus and compatible sensors
- Fixed: Cresta UV sensor temperature and extra data
- Fixed: CM119 total values
- Fixed: AlectoV1 Rain, Wind and Humidity values
- Changed: WH5029, Added battery state, fixed negative temperature, wind speed and wind direction values

RFLink v1.1 - R39: (11/3/2016)
- New Device: Fine Offset / Viking / WMS Mk3
- Fixed: Modified X10 security sensor pulse ranges
- Changed: Removed some "extra debug" information at the end of valid packets because Jeedom was skipping data

RFLink v1.1 - R38: (10/3/2016)
Note: Elmes changed into Keyloq you might have to re-learn the device..
- New Device: Initial NodoNRF sensor receive support (2.4ghz) (Thanks: Martinus)
- New Device: Nodo 3.8 slave support
- New Device: Catching of anti-tampering for Atlantic sensors
- New Device: Oregon, extra checks for out of range values
- New Device: Tunex MF-0211 temperature sensor
- New Device: Alecto V3 Rain - Alternative version of WS1200
- New Device: Byron SX21
- New Device: MC145026 based sensors
- New Device: FunkBus remote control support (Insta/Berker/Gira/Jung) (receive only) (Thanks: D.)
- New Device: Kingpin motor controls
- New Device: Livolo
- New Device: Koch remote controls
- New Device: Additional X10 protocol devices
- New Device: Forest "Touch Sense Motors" Curtain control (Thanks: JPe)
- New Device: Faher motor controller DC305, DC307
- New Device: Biltema 84056 temperature and humidity sensor
- New Device: Logipark
- New Device: Friedland EVO doorbell Decor ED1/ED3 (receive only)
- New Device: Friedland DC4 PIR
- New Device: Lobeco door sensors
- New Device: Hadex T093, WH5029
- New Device: FineOffset Temperature & Humidity sensors
- New Device: XT200 temperature sensor
- New Device: Conrad RSL blind controller 640579
- New Device: Smartwares SH5-TDR-A / SHS 5300 Heating Controller / Radiator Valve (Initial support)
- New Device: BFT port opener remotes (Thanks: CS.)
- New Device: Etekcity ZAP
- Added: Oregon, extra checks for out of range values
- Fixed: Oregon Rain sensors (PCR800 and others) (Thanks: D.)
- Fixed: Oregon humidity
- Fixed: Esic WT450H detection
- Fixed: Alecto V1 wind speed values
- Fixed: Alecto V3 Rain values and added battery level support (Thanks: D.)
- Fixed: EverFlourish EMW203T detection
- Fixed: Xiron/Aok humidity
- Fixed: Added more range checks on Aster protocol
- Fixed: Optimized Conrad RSl transmit function
- Fixed: Additional checks on Keeloq protocol
- Fixed: Additional checks on Chuango protocol
- Fixed: Improved EV1527 / Chuango recognition (some issues left)
- Fixed: Added support for the ProMax master buttons
- Fixed: Improved ProMax signal detection
- Fixed: Some changes to X10 command parsing (Thanks: JPe)
- Fixed: RTS increased broadcast time
- Fixed: Ikea Koppla transmit bug
- Fixed: Ikea Koppla dimming issue
- Fixed: Oregon wind speed
- Changed: Created a seperate Novatys plugin
- Changed: Smoke detectors now respond as a switch as well
- Changed: Corrected Elmes label into Keyloq label
- Changed: Splitted the WS1100/WS1200 plugin to improve compatibility
- Changed: Improved WS1200 signal handling
- Changed: Improved incoming command parsing
- Changed: Big speed-up for plugin 1 converted packets
- Changed: Regrouped plugins so new ones can be added more easily

RFLink v1.1 - R37: (23/01/2016)
- New Device: RTS transmit
- New Device: ProMax 75.0006.14 (Sold at Action)
- New Device: Novatys wall switches
- New Device: Perel 4 channel switch set
- New Device: Atlantic MD-210R
- New Device: Solight switch set
- Fixed: KD101 detection
- Fixed: GlobalTronics GT-WT-01, GT-WT-02
- Fixed: Alecto V4
- Fixed: Silvercrest switches
- Fixed: UPM/Esic negative temperature values
- Fixed: Oregon data processing speed improvement
- Fixed: Oregon V2 data processing and crc checks
- Fixed: Oregon RTGN318
- Fixed: Oregon wind speed
- Fixed: Humidity for BTHR918, BTHGN129, etc.
- Fixed: filtering out invalid packets for BTHR918, BTHGN129, etc.
- Fixed: Chacon remote control

RFLink v1.1 - R36: (13/01/2016)
- New Device: RF Environment Optimization System (Thanks: Snips)
- New Device: Maclean Energy MCE04 & 07 remote control and switches
- New Device: Brel DC90
- New Device: Medion MD 16179 doorbell (Receive only)
- New Device: Remote 546
- New Device: X10 security sensor protocol (a.o. Marmitek)
- New Device: Everflourish EMW100 / Cotech EMW100R (Thanks: J)
- New Device: Home Easy support for direct dim values
- New Device: SelectPlus Black Bell Button (non-A model)
- New Device: Silvercrest ian7443 type 10164 R RC202
- New Device: Atlantic's security sensors (receive only)
- New Device: (initial support for) FAAC TM signals (receive only)
- New Device: Oregon Scientific RTGN318
- New Device: WT0122 pool thermometer
- New Device: GlobalTronics GT-WT-01, GT-WT-02
- New Device: Rohrmotor24
- Changed: Removed temperature limits on LaCrosse/TFA
- Changed: Alecto V1 ID split (rolling code & channel number) for wind sensors
- Fixed: Ikea Koppla signal detection
- Fixed: Ikea Koppla dimming
- Fixed: Cresta sensor reporting period when there is low traffic
- Fixed: EMW200 transmit function
- Fixed: Lightwave RF transmit function
- Fixed: UPM/Esic minus temperature handling
- Fixed: OWL CM180 (Big thanks to Snips)
- Fixed: Various Oregon sensor optimizations (Big thanks to Snips)
- Fixed: WS3600 rounding of rain values for precision
- Fixed: WS3600 wind speed only passes one value at a time, Domoticz needs both. RFlink now passes the last know value for the non-received data
- Fixed: Improved Alecto V4 signal detection
- Fixed: Brel motor send command handling
- Fixed: BofuMotor send command handling
- Fixed: Elro Doorbell detection (among others: DB200Z, DB270)

RFLink v1.1 - R35: (8/12/2015)
- New Device: Full A OK Controller/Motor support
- New Device: Brel motor support
- New Device: Krippl temperature/humidity sensor support
- New Device: Elro DB270 doorbell
- New Device: InoValley SM302 Temperature&Humidity sensor (Thanks: Pirion)
- New Device: EZ6 Temperature&Humidity sensor
- New Device: Alecto SA30 & SA33 Smoke Alarm
- New Device: Xiron RS8751E3 Weather sensor
- New Device: LightwaveRF (initial support, testers needed)
- New Device: support for Oregon sensor simulator
- Fixed: Oregon OWL CM119, CM160, CM180
- Fixed: Oregon UV800 uv index value
- Fixed: Corrected WH440 temperature values
- Fixed: Improved Philips SBC
- Fixed: Improved Chacon EMW200
- Fixed: Improved FA500 false positive detection
- Fixed: Removed a slash in the UPM/Esic name
- Fixed: Mertik transmit improved
- Fixed: Optimized the Auriol/Xiron plugin
- Fixed: LaCrosse negative temperatures and extended allowed pulse range (Thanks: VeryBitter)
- Fixed: Alecto v1 Windspeed value
- Fixed: Improved Otio remote signal handling
- Fixed: corrected WH2 handling for Tesa WH1150 sensor (Thanks: Pirion)
- Fixed: Lacrosse rain - wind needs some more work (Thanks: Arie)
- Tested: tested and working: Lidl / Libra TR502MSV switches
- Tested: tested and working: Avidsen door contact 102359

RFLink v1.1 - R34: (7/11/2015)
- New Device: Heidemann HX Silverline 70290
- New Device: Eurochron EAS 301Z / EAS 302
- New Device: Znane-01 switch set sold at Biedronka (Impuls clone)
- New Device: HomeEasy HE800 protocol support
- New Device: Fine Offset Electronics WH2, Agimex Rosenborg 66796, ClimeMET CM9088
- New Device: Somfy Smoove Origin RTS (433mhz) (receive)
- New Device: Eurodomest 972086 (Sold at Action in Belgium)
- New Device: Eurodomest revised protocol (full autodetection)
- New Device: Prologue temperature sensor support
- New Device: tested and working: Home Confort, Smart Home PRF-100 switch set
- Fixed: Auto detection of "Emil Lux"/LUX-Tools remote control/switch set (Sold at Obi.de Art.Nr. 2087971) (Impuls clone)
- Fixed: Alecto WS1100 working properly again (Adjusted pulse range and displayed humidity value)
- Fixed: Byron SX receive and send commands
- Fixed: Ikea Koppla Send routines
- Fixed: Improved the Impuls remote detection
- Fixed: Impuls transmit
- Changed: added checks for valid temperatures in various plugins

RFLink v1.1 - R33: (20/10/2015)
- Updated RFlink loader to version 1.03 to include a serial log option with command sending ability!
- New Device: Full automatic 'Flamingo FA500/SilverCrest 91210/60494 RCS AAA3680/Mumbi M-FS300/Toom 1919384' protocol support! (send & receive!)
Note: re-learn your FA500 Remote in Domoticz
- New Device: Unitec 48111/48112 (receive)
- New Device: Avidsen sensors (pir/door contacts)
- New Device: Somfy Telis (433mhz) (receive)
- Fixed: Extreme temperature value rejection for various sensor types (TFA/LaCrosse)
- Fixed: Improved Blyss send routines
- Added: Support for old Xiron temperature sensor in Cresta plugin (Temperature only sensor was not handled)
- Added: Biowin meteo sensor
- Fixed: Imagintronix humidity and temperature values were sometimes incorrect
- Fixed: AB4400/Sartano/Phenix detection corrected
- Fixed: Modification to allow EMW200/203 to work better
- Changed: ARC (and compatible) remote and switch handling improved
- Fixed: Improved Impuls handling
- Fixed: Auriol V3 minus temperature handling
- Fixed: TRC02RGB send
- Fixed: Oregon OWL180 data
- Changed: Aster signal detection so that L^Home model 32311T is recognized as well
- Changed: ID for Nodo Slave 'Wind direction/Wind gust' combined so that Domoticz can handle the data
- Changed: Protocol handling order for 'multi-protocol' transmitting devices

RFLink v1.1 - R32: (2/10/2015)
- New Device: Europe RS-200, Conrad TR-200
- New Device: Bofu motor transmit
- New Device: ARC group command support
- New Device: Support for ARC based tri-state protocol
- New Device: Hormann (868mhz) receive (only some models using keeloq protocol)
- Changed: Bofu motor signal repetition detection improved
- Fixed: Aster transmit routines
- Fixed: plugin 003 output was not processed correctly by Domoticz
- Changed: Chacon/Powerfix/Mandolyn/Quigg transmit routine and optimized timing
- Changed: Increased the number of re-transmits in the Home Easy protocol to improve signal reception and distance
- Changed: Sensor plugins now suppressing ARC derived protocols a bit better

RFLink v1.1 - R31: (22/9/2015)
- New Device: Forrinx Wireless Doorbell
- New Device: TRC02 RGB controller
- New Device: OWL CM180
- New Device: ELMES CTX3H and CTX4H contact sensor
- New Device: Bofu Motor (receive)
- New Device: Aster / GEMINI EMC/99/STI/037
- Changed: EV1527 based sensors were reported as X10, now they are reported as EV1527. Note that it might be needed to re-add the devices to Domoticz
- Changed: increased number of retransmits for ARC and AC protocols
- Fixed: Koppla switch number was incorrect
- Fixed: Powerfix/Mandolyn/Chacon Parity calculation in send routines
- Fixed: Powerfix/Mandolyn/Chacon timing
- Fixed Windspeed value for WS2300
- Fixed: Home Easy HE300 ON/OFF signal was reversed
- Changed: HomeEasy suppressing additional protocol data to avoid reporting the same event multiple times under different protocols
- Fixed: More fixes to avoid duplicate reporting of the same event (various protocols)

RFLink v1.1 - R30:
- New Device: Conrad 9771 Pool Thermometer
- New Device: SilverCrest Z31370-TX Doorbell
- New Device: Smartwares remote controls (among others: SH5-TDR-K 10.037.17)
- New Device: Chuango Alarm devices Motion/Door/Window etc. (among others: CG-105S)
- New Device: Oregon Scientific NR868 PIR/night light
- New Device: Oregon Scientific MSR939 PIR
- New Device: Imagintronix Temperature/Soil humidity sensor
- New Device: Ikea Koppla
- New Device: Chacon (TR-502MSV, NR.RC402)
- Fixed: Arc protocol send
- Fixed: Impuls. Note: pair devices with the KAKU protocol, the remote is recognized separately
- Changed: Plugin 3 send method, combined routines
- Changed: HomeConfort was recognized as Impuls, now using GDR2 name
- Changed: HomeEasy remotes can deliver various signals, now skipping KAKU compatible signals and just reporting the HomeEasy code when both codes are transmitted
- Fixed: HomeEasy group on/off command was reversed for HE8xx devices, now correctly detects differences between HE3xx and HE8xx
- Fixed: HomeEasy was not able to control HE87x switches, changed the entire transmit routine
- Changed: stretched Xiron timing checks
- Changed: Various timing modifications (NewKaku/AC, Blyss) due to the new timing introduced at version R26
- Changed: Plugin 61, Chinese Alarm devices, reversed bits as it seemed to correspond better to bit settings, increased address range
- Fixed: Flamingo Smokedetector packet detection tightened up to prevent false positives
- Fixed: Corrected Conrad RSL command interpretation
- Added: Extended Nodo Slave support to support separate and combined sensors
- Added: Extended Nodo Slave support to support pulse meters

RFLink v1.1 - R29:
- Fixed: AC/NewKaku high unit numbers were incorrect.
If you already have devices with high unit numbers in Domoticz, just throw them away and let them be recognized again

RFLink v1.1 - R28:
- Fixed: FA20RF smoke detector transmit from Domoticz

RFLink v1.1 - R27:
- Added: OSV1 battery status
- Fixed: OSV1 boundaries and removed some debug info
- Fixed: Some plugins set an incorrect sampling rate divider value
- Changed: AlectoV1 false positives filter was too agressive

RFLink v1.1 - R26: - Added: QRFDEBUG command to do faster logging of undecoded data
- Added: VERSION command
- Added: Powerfix/Quigg switches
- Added: proper Lacrosse V3 WS7000 sensor support
- Changed: config file and plugin integration
- Changed: timeout and divider value
- Changed: Lacrosse V2 WS2300/WS3600 plugin number to get faster processing, changed various other parts as well
- Changed: Lacrosse V1 pulse duration checks
- Changed: various parts to improve speed
- Changed: Flamingo Smoke detector signal re-transmits from 8 to 10 times
- Added: Additional tests on Alecto V1 and Alecto V4 to filter out false positives
- Fixed: AC (NewKaku) protocol send for some device numbers
- Fixed: little bug in UPM code
- Fixed: Oregon wind speed reporting
- Fixed: Wind speed calculations
- Fixed: Wind direction reporting in all plugins
- Fixed: AlectoV3 humidity value displaying out of range values
- Fixed: OregonV1 decoding

RFLink v1.1 - R25:
- Fixed: Eurodomest address range check
- Fixed: Alecto V1 and V3 humidity handling
- Fixed: Lacrosse WS2300/WS3600 and labelled as LacrosseV2

RFLink v1.1 - R24:
- Fixed: Flamingo Smoke Detector timings and device address usage
- Fixed: Timing for Nexa/Jula Anslut

RFLink v1.1 - R23:
- Changed: Alecto V1 temperature data filtering
- Added: Alecto V1 battery status now shown for temperature sensors

RFLink v1.1 - R22:
- Various additional tests and fixes after intensive tests
- Added: Home Confort send and recognition by Domoticz

RFLink v1.1 - R21:
- Re-Activated PIR & Door/Window sensors (plugin 60/61)

RFLink v1.1 - R20:
- Switched to Arduino 1.6.5

RFLink v1.1 - R19:
- Complete rewrite
- Added: Home Confort Smart Home - TEL-010
- Added: RGB LED Controller
- Added: RL-02 Digital Doorbell
- Added: Deltronic Doorbell
- Added: Sartano 2606 remote & switch

RFLink v1.1 - r18: - Added Banggood SKU174397, Sako CH113, Homemart/Onemall FD030 and Blokker (Dake) 1730796 outdoor temperature sensor
- Tested Okay: Promax RSL366T, Profile PR-44N & PR-47N
- Fixed: LaCrosse humidity values are correctly displayed
- Fixed: Humidity values that originate from slave Nodos are correctly displayed
- Fixed: UPM/Esic insane temperature values are skipped
- Removed Xiron & Auriol debug data
- Tightened pulse range on various protocols to prevent false positives

RFLink v1.1 - r17:
- Modified Oregon THGR228N code
- Modified Newkaku(AC) dim values
- Corrected support for KAKU door switches
- Fixed Nodo Slave sensors
- Improved speed and priorities so that group commands are properly transmitting

RFLink v1.1 - r16:
- Fixed Aleco V1 temperature ID to match wind sensors
- Fixed HomeEasy transmit
- Added AC(NewKaku) dimmer support

RFLink v1.1 - r15:
- Improved large packet translation

RFLink v1.1 - r14:
- Changed Motion sensors (60/61)

RFLink v1.1 - r13:
- Flamingo Smoke detector fix
- Added Xiron sensor support

RFLink v1.1 - r11/12:
- Mertik / Dru Send added

RFLink v1.1 - r10:
- Added Auriol Z32171A

RFLink v1.1 - r9:
- Fixed Kaku send with high device id's (P1 M1 etc)

RFLink v1.1 - r8:
- Improved descriptions

RFLink v1.1 - r7:
- Fixed Oregon RTGR328N ID and humidity format
- Fixed UPM/Esic humidity format
- Fixed Alecto humidity format

RFLink v1.1 - r6:
- Fixed Auriol V2 plugin
- Updated Auriol plugin
- Fixed Lacrosse Humidity

RFLink v1.1 - r1/2/3/4/5:
- Added X10 receive/transmit plugin
- Minor changes & improvements

Special thanks to everyone who contributed with feedback, suggestions, debug data, tests and even complete protocol plugins!