RFLINK
FREE - Easy to use - More protocols than any other solution - Multiple frequencies - Multiple home automation platforms

New RFLink firmware (R47) now available!

15 September 2017

Firmware release 47 adds support for many new devices and contains various improvements and extensions.
Below you can find the list of changes and additions.

There were a many devices that identify themselves incorrectly when compared to existing protocol implementations. The reason is simple, the manufacturer does not care if his product is not compatible with an existing product. To solve the issues, RFLink now has a special mode where you can teach it signals and store those into the RFLink's EEPROM memory. Yes it also survives firmware updates. Once a signal is identified and stored it will be recognized automatically!. Here you can find an explanation.

The new firmware is now available on the Firmware download page or by clicking this link:
RFLink firmware R47

If you use Jeedom or IOBroker, firmware updates can be done through the program itself.
For other home automation software we are working on similar solutions, until then you need to do the update manually.

The RFlink Gateway supports more protocols and frequencies than any other device out there and the best of all... it is completely FREE!
If you like this project there are various ways you can support us, it is much appreciated.

Note that we still have lots of debug data that is currently being analysed to be added to the RFLink code.
Also we have many support requests that we are working on. However, there are so many requests that it is hard to answer all prmptly. If you did not get a reply or solution yet, please know that we are working on it and have not forgotten. Also, we are making good progress with various 868mhz and 2.4Ghz devices. More protocols and hardware is being tested for the next release.

Enjoy!
Stuntteam

R47: (15/09/2017)
- New Device: Micro Tybox X2D / Tybox H X2D Thermostats (works with 433 and/or 868 mhz)
- New Device: Tybox 310 X2D Thermostat (868mhz)
- New Device: Delta Dore - Deltia 8.03 X2D Thermostat (868mhz)
- New Device: TYXIA 261/461 X2D micro modules (868mhz) (Receive only, more logs needed)
- New Device: Milight RGB+CCT (a.o. 4-zone FUT092/ 8-zone FUT089)
- New Device: Milight RGB (a.o. FUT098)
- New Device: Bofu motor BF-301, EY1612, EY1624 and others
- New Device: Oregon Scientific SL109
- New Device: AR53002 / AR50055 X2D Thermostats
- New Device: Atlantic MD-210R / Focus MD-210R - 868mhz door contact
- New Device: Legrand CAD Radio
- New Device: Gelia EMW100T switch set
- New Device: ELEC EDB-40 / QH-1085TX V1.1 Quhwa doorbell
- New Device: X10 Sensors
- New Device: Ambient FT004T temperature sensor
- New Device: Ambient FT004B temperature sensor
- New Device: ASA radio technology Go-1
- New Device: Telis 4 Modulis RTS
- New Device: Added support for a new version of the Rubicson WT0122 pool thermometer
- New Device: Renkforce E0190TA and compatible temperature sensors
- New Device: Ematronic AC114-01B shutter/blinds controller
- New Device: Yooda Melody shutter/blinds controller
- New Device: Viking 02813 Temperature sensor
- New Device: Marquant 943134 Temperature sensor
- New Device: Arlec RC10 switch set
- New Device: V2 Phoenix remote signals (Receive only)
- New Device: IDK CAR-200 doorbell (Receive only)
- New Feature: GPIO pin state at boot can be selected with a wire from pin 5 to ground to set the pin default to high
- Added: X2D/X3D protocol support
- Added: Milight RGB and RGB+CCT protocol support
- Added: Direct dimming support for Flamingo and compatible devices
- Added: Additional WH3 detection
- Added: Two Additional Dooya protocol flavors
- Added: Additional Dooya signal recognition
- Added: Additional Blyss remote control recognition
- Added: Additional Brell remote control recognition
- Added: STOP command support to (first) extended RTS protocol version
- Added: Support for second extended RTS protocol version
- Added: Additional Pair option for Bofu motor devices
- Added: upon request added 6 additional GPIO pin's for generic use
The GPIO pins are often used to 'press buttons' on incompatible devices
- Fixed: Added pairing command for Ansluta
- Fixed: Increased transmission duration for Ansluta
- Fixed: corrected barometric pressure value of BTHR918
- Fixed: UPM Esic negative temperatures
- Fixed: Further improved X10 protocol detection
- Fixed: 'newkaku' send command handling improved
- Fixed: 'newkaku' group commands put at a unique switch number
- Fixed: imrpoved newkaku filtering
- Fixed: improved Acurite SL109 negative temperature handling
- Fixed: CM113 ampere precision
- Fixed: Milight: bug in unit selection
- Fixed: bug with the number of RFCustom records
- Fixed: removal of RFCustom records
- Fixed: Improved Xiron sensor detection
- Fixed: Alecto rain meter values


New RFLink firmware (R46) now available!

11 March 2017

Firmware release 46 adds support for many new devices and contains various improvements and extensions.
Below you can find the list of changes and additions.

There were a many devices that identify themselves incorrectly when compared to existing protocol implementations. The reason is simple, the manufacturer does not care if his product is not compatible with an existing product. To solve the issues, RFLink now has a special mode where you can teach it signals and store those into the RFLink's EEPROM memory. Yes it also survives firmware updates. Once a signal is identified and stored it will be recognized automatically!. Here you can find an explanation.

We also included a new version of the RFLink Loader program.

The new firmware is now available on the Firmware download page or by clicking this link:
RFLink firmware R46

If you use Jeedom or IOBroker, firmware updates can be done through the program itself.
For other home automation software we are working on similar solutions, until then you need to do the update manually.

The RFlink Gateway supports more protocols and frequencies than any other device out there and... it is FREE!
If you like this project there are various ways you can support us, it is much appreciated.

Note that we still have lots of debug data that is currently being analysed to be added to the RFLink code.
Also, we are making good progress with various 868mhz and 2.4Ghz devices. More on that soon.

Enjoy!
Stuntteam

R46: (10/03/2017)
- New Device: Applidom DM82 motion sensor
- New Device: OWL Intuition PV / CM180i
- New Device: WH2A temperature sensors
- New Device: WH1285 TX (WH-5) Temp & Humidity sensor
- New Device: ABB lightswitch type 3299a-11900 (a.k.a. TX Tango) (Receive only!)
- New Device: Velleman VM130T Motor control
- New Device: HRC 101 Motor control
- New Device: AC512-02 AC to RF projection screen trigger
- New Device: 2 new Dooya protocol flavors
- New Device: D-YA / Diya Motor control
- New Device: Konx doorbell model 602 (Receive only!)
- New Device: Doorman doorbell (Receive only!)
- New Device: Acurite 3in1 3N1TXR / 3N1TXC (Thanks: JR)
- New Device: Byron BY532E (Receive only!)
- New Device: Stagnoli remotes
- New Device: Blyss temperature sensors (Ref.630467) (Thanks: JD)
- New Device: Grundig QH-831A 2010525 & Quhwa QH-831A doorbell
- New Device: 868mhz: Woonveilig security sensors
- New Device: 868mhz: Egardia security sensors
- New Device: 868mhz: Alecto WS3900
- New Device: Yale HSA3000/6000 alarm system sensors
- New Device: Sartano 50080 (Harald Nyborg 2794) switch set
- New Device: Astrell 85 portal motorization system
- New Device: Philips AJ7010/12
- New Feature: Learn RF device signals that use a standard EV1527/PT2262 protocol
- Fixed: Some small eeprom handling issues
- Fixed: Improved AI protocol priority handling
- Fixed: various CC2500 issues, make sure pin 6 is wired to ground to use CC2500!
- Fixed: Tightened Warema EWFS detection
- Fixed: RTSlongTX command
- Fixed: ON/OFF vs UP/DOWN command handling
- Fixed: UPM Esic extended packet detection and increased sanity checks on data
- Fixed: Optimized Novatys timing
- Fixed: AlectoV3 Humidity value validation
- Fixed: FineOffset vs Alecto improved differentiation, Note: device ID's have changed for WS1100
- Fixed: Alecto WS-1100 humidity
- Fixed: AlectoV4 Some packets contained an invalid temperature
- Fixed: Globaltronics GT-WT-02 negative temperature/channel number mixup
- Fixed: Globaltronics GT-WT-02 now always reporting a humidity
- Fixed: Tristate send, removed debug message and fixed a timing bug
- Fixed: WS7000 rain reporting
- Fixed: Added additional Brel protocol variant
- Fixed: LightwaveRF turned MOOD commands into regular switch commands so any home automation software can use them
- Fixed: Improved Friedland doorbell signal detection
- Fixed: Acurite 5in1 corrected wind speed, wind direction and rainfall values (Thanks: Xztraz.)
- Fixed: Improved AcuRite 00592TXR detection
- Fixed: Tunex zero humidity value
- Fixed: Improved Home Confort transmit routine and added up/down support (Thanks: Geert)
- Fixed: Battery detection in Prologue protocol
- Fixed: Added channel number to device ID for THGR810
- Fixed: Added channel number support to Warema devices
- Fixed: Improved UPM ESIC protocol detection
- Fixed: Improved SA33 detection
- Fixed: Gaposa protocol timing
- Added: battery status on various Alecto/Maplin devices (Thanks: Ad)
- Added: Hardware & Software configuration via i/o pins:
pin 6 to ground for: CC2500 enable
pin 7 to ground for: disable internal pull-up on RF data in
pin 12 to ground for: reset of EEPROM settings


New RFLink firmware (R45) now available!

07 December 2016

Firmware release 45 adds support for many new devices and contains various improvements and extensions.

The new firmware is now available on the Firmware download page.
There you can also find the change log to see what is new and what has changed in this firmware release.
If you use Jeedom or IOBroker, firmware updates can be done through the program itself.
For other home automation software we are working on similar solutions, until then you need to do the update manually.

RFlink is the most user friendly, cheapest, modular and flexible RF Gateway on the globe!


New RFLink firmware (R44) now available!

26 October 2016

Brand new RFLink Gateway firmware adds support for Ikea Ansluta, Philips Living Colors Gen1, MySensors devices and has "Mini" GPIO.
For Ansluta or Living Colors you will need a CC2500 module. Details on how to connect these modules are on the Wiring details page.
Check out the FAQ for more information.

The new firmware is now available on the Firmware download page.
There you can also find the change log to see what is new and what has changed in this firmware release.
If you use Jeedom, firmware updates can be done through Jeedom itself.
For other home automation software we are working on similar solutions, until then you need to do the update manually.

433Mhz, 868Mhz, 2.4 Ghz, MiLight, MySensors, Ikea Ansluta, Philips Living Colors, GPIO and much more..
RFlink is the most friendly, cheapest, modular and flexible RF Gateway on the globe!


Latest News:
Development progress update

05 October 2016

Good news from the lab guys..!
Philips Living Colors Generation-1 remote control commands can be received and lamps can be controlled with RFlink when a CC2500 transceiver is connected.
Also the Ikea Ansluta (YH-KZQ-FS) remote control commands can be received and lamps can be controlled!
RFLink is the most flexible and only true RF Gateway solution!
PLC ANS OML

Besides that we are still investigating the protocol of the new MiLight RGBWW devices and solved some parts of the puzzle.
Further more we are also looking at integrating support for CC1101 modules to control Itho ventilation units and other protocols that use 868 mhz FSK and we are looking at integrating the NRF905 - 868 transceivers.
RFlink also will get support for I/O pins so that devices connected to I/O can be controlled and their status can be seen.

Besides the above, we continue to work on new/unsupported 433mhz devices and check some reported issues

If you have any hardware (remotes/sensors/transceiver modules etc) that you want to donate to the project feel free to email to frankzirrone@gmail.com

WANTED:
We are looking for people who can help with integrating RFLink into Home Automation software programs.
Contact us if you are interested!


New RFLink firmware (R43) now available!

23 September 2016

A new firmware version has been released. It is available on the Firmware download page.
There you can also find the change log to see what is new and what has changed in this firmware release.
If you use Jeedom, firmware updates can be done through Jeedom itself.
For other home automation software we are working on similar solutions, until then you need to do the update manually.

Release 43 includes a long list of changes and additions but unfortunately some things were not ready for the release. Because we did not want to delay the release any further some new features and changes have been moved to the next release which will be made available soon.


Development progress update

23 June 2016

Right now we are looking at integrating support for CC2500 RF modules to support Ikea Ansluta and first generation Philips Living Colors lamps.
Besides that we are investigating the protocol of the new MiLight RGBWW devices. Furthermore we are working on MySensors device capture integration.

We are also working on improving the MiLight implementation.
Right now it works more or less okay in both receiving and transmitting of signals when it comes to the implementation of at least 2 RGBW remotes.
These 2 remotes already have small differences in their signals and it appears that there is another branch of remotes that has some issue with the behaviour of how zones are controlled.
If you have this issue or are experiencing any other issue with MiLight and want to help, you can check the development page and make a debug log of the buttons of your remote control.

Besides log data from new/unsupported 433mhz devices, there are also several small issues reported.
Some can be implemented/fixed quickly, others take more time to analyse. Obviously we continue to work on this.

If you have any hardware (remotes/sensors etc) that you want to donate to the project feel free to email to frankzirrone@gmail.com


RFLink now fully supports MiLight bulbs, remotes and bridges

09 June 2016

The most flexible RF Gateway now got even more flexible. By adding a NRF24L01 to your RFLink Gateway you can now control any MiLight bulb and capture the signals from MiLight remote controls and wifi bridges. RFlink makes it possible to control up to 262140 unique devices.
Check the wiring page for the exact details on how to add the NRF24L01 to your RFLink setup.
Also make sure you are using the latest RFLink firmware!


Support the project:

The RFLink Firmware development is a freeware project. This means you should not pay for the firmware.
We are not linked to any shops and do not have unlimited resources to buy sensors and devices.
You can support the project by sending in debug data for new sensors, send hardware or
make a donation so we can buy sensors you would like to see supported.